By Cyrielle Marjolaine. Motor. Publised at Thursday, June 29th 2017, 01:05:11 AM. The motor power output (speed times torque) is determined by the power supply voltage and the motor’s inductance. The motor’s output power is proportional to the power supply voltage divided by the square root of the motor inductance.
By Jessica Mireille. Car Wiring. Published at Sunday, December 31st 2017, 16:28:47 PM. There are many fuses, each protecting a small group of components, so that one blown fuse does not shut down the whole system. Many of the fuses are grouped together in a fuse box, but there may also be line fuses in the wiring.
By Madeleine Catherine. Motor. Published at Sunday, December 31st 2017, 15:23:47 PM. A step motor is a constant output power transducer, where power is defined as torque multiplied by speed. This means motor torque is the inverse of motor speed. To help understand why a step motor’s power is independent of speed, we need to construct (figuratively) an ideal step motor.
By Madeleine Catherine. Circuit. Published at Sunday, December 31st 2017, 14:51:43 PM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Jessica Mireille. Car Wiring. Published at Sunday, December 31st 2017, 12:05:54 PM. When you begin the rewiring of your car, choose good material, as in new wire and quality terminals. Use a gauge of wire sufficient to carry the amperage load for the work it will be doing. Always use closed-end terminals, not the U type.
By Madeleine Catherine. Motor. Published at Sunday, December 31st 2017, 11:43:49 AM. At this point it is important to introduce the concept of overdrive ration. This is the ration between the power supply voltage and the motor’s rated voltage. An empirically derived maximum is 25:1, meaning the power supply voltage should never exceed 25 times the motor’s rated voltage or 32 times the square root of motor inductance. Below is a graph of measured iron losses for a 4A, 3V motor. Notice in Figure 16 how the iron losses range from insignificant to being the major cause of heating in the motor compared to a constant 12W copper loss (4A times 3V).
By Cyrielle Marjolaine. Diagram. Published at Sunday, December 31st 2017, 06:27:36 AM. Circuits often require inputs that come directly from users (as opposed to inputs that come from other devices). User-input devices can take many forms, among them keyboards (as on a PC), buttons (as on a calculator or telephone), rotary dials, switches and levers, etc. Digilent boards include several input devices, typically including push buttons and slide-switches. Since digital circuits operate with two voltage levels (LHV or Vdd, and LLV or GND), input devices like buttons and switches should be able to produce both of these voltages based on some user action.
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 23:20:44 PM. On all but the simplest PCBs, wires must be printed on more than one surface of fiberglass to allow for all the required component interconnections. Each surface containing printed wires is called a layer. In a relatively simple PCB that requires only two layers, only one piece of fiberglass is required since wires can be printed on both sides. In a more complex PCB where several layers are required, individual circuit boards are manufactured separately and then laminated together to form one multi-layer circuit board. To connect wires on two or more layers, small holes called vias are drilled through the wires and fiberglass board at the point where the wires on the different layers cross. The interior surface of these holes is coated with metal so that electric current can flow through the vias. Most Digilent boards are simple four or six layer boards; some more complex computer circuit boards have more than 20 layers.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.