By Cyrielle Marjolaine. Motor. Publised at Thursday, June 29th 2017, 01:05:11 AM. The drive remedies this instability by adding a second-order, or viscous, damping. This damping decreases the total phase lag so the motor cannot sustain oscillation, much in the same way shock absorbers damp the mass-spring suspension of a vehicle.
By Madeleine Catherine. Circuit. Published at Saturday, August 05th 2017, 15:56:27 PM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.
By Bertille Solange. Diagram. Published at Thursday, August 03rd 2017, 15:32:42 PM. The voltage source, such as a battery, is needed in order to cause the current to flow through the circuit. In addition, there needs to be a conductive path that provides a route for the electricity to flow. Finally, a proper circuit needs a load that consumes the power.
By Alix Loane. Diagram. Published at Saturday, July 29th 2017, 15:03:18 PM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Sasha Sara. Diagram. Published at Friday, July 28th 2017, 13:28:14 PM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Sasha Sara. Diagram. Published at Tuesday, July 25th 2017, 11:46:43 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Cyrielle Marjolaine. Diode. Published at Saturday, July 22nd 2017, 10:45:28 AM. A simplified planar silicon diode is illustrated in Fig. 2.0.3. Using this process for silicon diodes produces two differently doped layers of silicon, which form a ‘PN junction’. Undoped or ‘intrinsic’ silicon has a lattice structure of atoms, each having four valence electrons, but P type silicon and N type silicon are doped by adding a relatively very small amount of material having either an atomic structure with three valence electrons (e.g. Boron or Aluminium) to make P type, or five valence electrons (e.g. Arsenic or Phosphorus) to make N type silicon. These doped versions of silicon are known as ‘extrinsic’ silicon. The P type silicon now has a shortage of valence electrons in its structure, which can also be considered to be a surplus of ‘holes’ or positive charge carriers, whereas the N type layer is doped with atoms having five electrons in its valence shell and therefore has a surplus of electrons which are negative charge carriers.
By Sasha Sara. Diagram. Published at Thursday, July 20th 2017, 10:43:41 AM. The unloaded PCB appears green because thin sheets of green plastic have been applied to both sides (otherwise the PCB would appear pale yellow). Called solder masks, these sheets cover all exposed metal other than the component pads and holes so that errant solder can not inadvertently short (or electrically connect) the printed wires. All metal surfaces other than the exposed pads and holes (i.e., the wires) are underneath the solder mask. Not infrequently, blue or even red solder masks are used.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.