By Alix Loane. Power. Publised at Wednesday, November 29th 2017, 09:01:12 AM. The linear regulator is the basic building block of nearly every power supply used in electronics. The IC linear regulator is so easy to use that it is virtually foolproof, and so inexpensive that it is usually one of the cheapest components in an electronic assembly.
By Alix Loane. Diagram. Published at Monday, August 21st 2017, 02:43:00 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
By Valentine Sybille. Diagram. Published at Saturday, August 19th 2017, 00:16:17 AM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Charlotte Myriam. Circuit. Published at Thursday, August 17th 2017, 22:51:19 PM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.
By Bertille Solange. Circuit. Published at Tuesday, August 15th 2017, 22:28:56 PM. Electronic signals are represented either by voltage or current. The timedependent characteristics of voltage or current signals can take a number of forms including DC, sinusoidal (also known as AC), square wave, linear ramps, and pulsewidth modulated signals. Sinusoidal signals are perhaps the most important signal forms since once the circuit response to sinusoidal signals are known, the result can be generalized to predict how the circuit will respond to a much greater variety of signals using the mathematical tools of Fourier and Laplace transforms.
By Cyrielle Marjolaine. Circuit. Published at Monday, August 14th 2017, 20:40:30 PM. The real part and imaginary part of impedance are interpreted as a resistive part that dissipates energy and a reactive part that stores energy. Resistors can only dissipate energy and therefore their impedances have only a real part. Capacitors and inductors can only store energy and therefore their impedances have only an imaginary part. When resistors, capacitors, and inductors are combined, the overall impedance may have both real and imaginary parts. It is important to note that the definition of impedance preserves the definition of resistance.
By Valentine Sybille. Diagram. Published at Friday, August 11th 2017, 20:20:28 PM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Cyrielle Marjolaine. Circuit. Published at Wednesday, August 09th 2017, 17:27:34 PM. An intuitive way to understand the behavior of voltage and current in electronic circuits is to use hydrodynamic systems as an analogue. In this system, voltage is represented by gravitational potential or height of the fluid column, and current is represented by the fluid flow rate.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.