By Madeleine Catherine. Circuit. Publised at Saturday, August 05th 2017, 15:56:27 PM. The real part and imaginary part of impedance are interpreted as a resistive part that dissipates energy and a reactive part that stores energy. Resistors can only dissipate energy and therefore their impedances have only a real part. Capacitors and inductors can only store energy and therefore their impedances have only an imaginary part. When resistors, capacitors, and inductors are combined, the overall impedance may have both real and imaginary parts. It is important to note that the definition of impedance preserves the definition of resistance.
By Alix Loane. Diagram. Published at Saturday, December 30th 2017, 20:00:37 PM. Circuit components are manufactured with exposed metal pins (or leads) that are used to fasten them to the PCB both mechanically (so they will not fall off) and electrically (so current can pass between them). The soldering process, which provides a strong mechanical bond and a very good electrical connection, is used to fasten components to the PCB. During soldering, component leads are inserted through the holes in the PCB, and then the component leads and the through-hole plating metal are heated to above the melting point of the solder (about 500 to 700 degrees F). Solder (a metallic compound) is then melted and allowed to flow in and around the component lead and pad. The solder quickly cools to form a strong bond between the component and the PCB. The process of associating components with reference designators, loading them into their respective holes, and then soldering them in place comprises the PCB assembly process.
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 17:52:52 PM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 30th 2017, 17:29:18 PM. Most electronic circuits can be represented as a system with an input and an output. The input signal is typically a voltage that is generated by a sensor or by another circuit. The output signal is also
By Valentine Sybille. Car Wiring. Published at Saturday, December 30th 2017, 13:36:45 PM. Plan the route of the wires. There are some wires that should not come in close proximity to other wires. The radio wires must be kept clear of the ignition wires to reduce interference.
By Valentine Sybille. Car Wiring. Published at Saturday, December 30th 2017, 12:56:44 PM. When fitting extra accessories, such as a rear window heater which consumes a heavy current, always wire it through the ignition switch. Some ancillary components can be operated without the ignition turned on by turning the switch to the "auxiliary" position. A radio is usually wired through this switch, so that it can be played with the engine off.
By Cyrielle Marjolaine. Car Wiring. Published at Saturday, December 30th 2017, 12:48:04 PM. As you know, a diesel engine differs from other liquid fuel engines in one major respect: the fuel/air charge is ignited by cylinder pressure and resulting heat, instead of via an electrical ignition system (diesel-fueled engines don’t use spark plugs).
By Charlotte Myriam. Car Wiring. Published at Saturday, December 30th 2017, 08:57:08 AM. Wire and cable sizes are classified by the maximum amperage that they can carry safely. A complex network of wires runs through the car. To avoid confusion, each wire is colour coded (but only within the car: there is no national or international system of colour-coding).
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.