By Sasha Sara. Diagram. Publised at Tuesday, July 25th 2017, 11:46:43 AM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).
By Bertille Solange. Circuit. Publised at Wednesday, December 20th 2017, 07:45:00 AM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.
By Madeleine Catherine. Motor. Published at Sunday, December 31st 2017, 11:43:49 AM. A step motor is highly resonant because it is a mass-spring system. The “mass” portion is the rotor and load inertia while the “spring” portion is the restoring torque of the magnetic field that drags the rotor along. Because of this, velocity lags torque by 90 degrees.
By Cyrielle Marjolaine. Diagram. Published at Sunday, December 31st 2017, 06:27:36 AM. A capacitor is a two-terminal device that can store electric energy in the form of charged particles. You can think of a capacitor as a reservoir of charge that takes time to fill or empty. The voltage across a capacitor is proportional to the amount of charge it is storing – the more charge added to a capacitor of a given size, the larger the voltage across the capacitor. It is not possible to instantaneously move charge to or from a capacitor, so it is not possible to instantaneously change the voltage across a capacitor. It is this property that makes capacitors useful on Digilent boards and in many other applications.
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 23:20:44 PM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Sasha Sara. Car Wiring. Published at Saturday, December 30th 2017, 22:08:32 PM. If your terminal is attached by a nut to a post, use lock washers and if it is a very important connection, and most are, use blue Loctite on the post. Many electrical failures are random and due to loose connections that are hard to trace. A quick look and the connection looks good, but if it is loose, it will cause an interruption of the current flow periodically.
By Alix Loane. Diagram. Published at Saturday, December 30th 2017, 20:00:37 PM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 17:52:52 PM. When working with circuits, you will often find something called a schematic diagram. These diagrams use symbols to illustrate what electronic components are used and where they’re placed in the circuit. These symbols are graphic representations of the actual electronic components.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 30th 2017, 17:29:18 PM. Electrical components such as resistors, capacitors, inductors, and transistors can all be represented by equivalent mechanical devices that support this analogy.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.