By Lydie Honorine. Diagram. Publised at Sunday, November 19th 2017, 20:50:47 PM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Madeleine Catherine. Diagram. Publised at Sunday, November 19th 2017, 21:57:33 PM. A first look at a circuit diagram may be confusing, but if you can read a subway map, you can read schematics. The purpose is the same: getting from point A to point B. Literally, a circuit is the path that allows electricity to flow. If you know what to look for, it’ll become second nature. While at first you’ll just be reading them, eventually you will start creating your own. This guide will show you a few of the common symbols that you are sure to see in your future electrical engineering career.
By Charlotte Myriam. Circuit. Published at Friday, December 22nd 2017, 07:40:14 AM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.
By Charlotte Myriam. Circuit. Published at Thursday, December 21st 2017, 23:38:50 PM. There are two kinds of energy sources in electronic circuits: voltage sources and current sources. When connected to an electronic circuit, an ideal voltage source maintains a given voltage between its two terminals by providing any amount of current necessary to do so. Similarly, an ideal current source maintains a given current to a circuit by providing any amount of voltage across its terminals necessary to do so.
By Valentine Sybille. Circuit. Published at Thursday, December 21st 2017, 21:52:39 PM. Electrical components such as resistors, capacitors, inductors, and transistors can all be represented by equivalent mechanical devices that support this analogy.
By Alix Loane. Diagram. Published at Thursday, December 21st 2017, 20:20:32 PM. When working with circuits, you will often find something called a schematic diagram. These diagrams use symbols to illustrate what electronic components are used and where they’re placed in the circuit. These symbols are graphic representations of the actual electronic components.
By Madeleine Catherine. Diagram. Published at Thursday, December 21st 2017, 18:30:58 PM. The slide switches are also known as “single throw-double pole” (STDP) switches, because only one switch (or throw) exists, but two positions (or poles) are available (a pole is an electrical contact to which the switch can make contact). These switches can be set to output either Vdd (when the actuator is closest to the board’s edge) or GND. The push button switches are also known as “momentary” contact buttons, because they only make contact while they are actively being pressed – they output a GND at rest, and a Vdd only when they are being pressed. The figure below shows typically pushbutton and slide switch circuits used on Digilent boards.
By Lydie Honorine. Circuit. Published at Thursday, December 21st 2017, 17:47:49 PM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.
By Valentine Sybille. Circuit. Published at Thursday, December 21st 2017, 17:19:51 PM. Voltage is measured in units of Joules per Coulomb, known as a Volt (V). It is important to remember that voltage is not an absolute quantity, rather, it is always considered as a relative value between two points. In an electronic circuit, the electromagnetic problem of voltages at arbitrary points in space is typically simplified to voltages between nodes of circuit components such as resistors, capacitors, and transistors
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.