By Jessica Mireille. Circuit. Publised at Monday, December 18th 2017, 14:08:09 PM. The real part and imaginary part of impedance are interpreted as a resistive part that dissipates energy and a reactive part that stores energy. Resistors can only dissipate energy and therefore their impedances have only a real part. Capacitors and inductors can only store energy and therefore their impedances have only an imaginary part. When resistors, capacitors, and inductors are combined, the overall impedance may have both real and imaginary parts. It is important to note that the definition of impedance preserves the definition of resistance.
By Valentine Sybille. Diagram. Published at Saturday, January 06th 2018, 17:30:41 PM. A block diagram shows a higher level (or organizational layout) of functional units in a circuit (or a device, machine, or collection of these). It is meant to show data flow or organization between separate units of function. A block diagram gives you an overview of the interconnected nature of circuit assemblies or components.
By Alix Loane. Diagram. Published at Saturday, January 06th 2018, 15:25:58 PM. On all but the simplest PCBs, wires must be printed on more than one surface of fiberglass to allow for all the required component interconnections. Each surface containing printed wires is called a layer. In a relatively simple PCB that requires only two layers, only one piece of fiberglass is required since wires can be printed on both sides. In a more complex PCB where several layers are required, individual circuit boards are manufactured separately and then laminated together to form one multi-layer circuit board. To connect wires on two or more layers, small holes called vias are drilled through the wires and fiberglass board at the point where the wires on the different layers cross. The interior surface of these holes is coated with metal so that electric current can flow through the vias. Most Digilent boards are simple four or six layer boards; some more complex computer circuit boards have more than 20 layers.
By Jessica Mireille. Motor. Published at Saturday, January 06th 2018, 12:30:19 PM. The result will be in microfarads for the capacitor if the value for “I” is amperes of current needed and “V” is the output voltage of the supply. When picking the capacitor, any value equal to or greater than the calculated value can be used. Be sure to use a capacitor with a voltage rating at least 20% higher than the output voltage of the power supply.
By Alix Loane. Motor. Published at Saturday, January 06th 2018, 07:22:36 AM. The voltage of your power supply is entirely dependent on the inductance rating of your motor, which we learned is translatable to the number of turns of wire in the stator. Every motor model will have a different inductance rating and will therefore have a different maximum voltage. To figure out what the maximum power supply voltage should be, use the following formula with the motor’s inductance in millihenries (mH) used for the L value.
By Charlotte Myriam. Motor. Published at Friday, January 05th 2018, 22:53:04 PM. The power output decreases with speed because of the constant-torque loss due to detent torque and other losses. The same effect causes a slight decrease in torque with speed in the constant torque region as well. Finally, there is a rounding of the torque curve at the corner speed because the drive gradually transitions from being a current source to being a voltage source. The drive limits current to the motor below the corner speed and thus is a current source. Above the corner speed, the motor’s inductive reactance limits the current and the drive becomes a voltage source as it applies all of the power supply voltage to the motor.
By Valentine Sybille. Diagram. Published at Friday, January 05th 2018, 22:02:27 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
By Sasha Sara. Motor. Published at Friday, January 05th 2018, 18:24:19 PM. A real step motor has losses that modify the ideal speed-torque curve. The most important effect is the contribution of detent torque. Detent torque is usually specified in the motor datasheet. It is always a loss when the motor is turning and the power consumed to overcome it is proportional to speed. In other words, the faster the motor turns the greater the detent torque contributes power loss at the motor’s output shaft. This power loss is proportional to speed and must be subtracted from the ideal, flat output power curve past the corner speed. This now constitutes a practical speed-torque curve.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.