By Jessica Mireille. Circuit. Publised at Monday, December 18th 2017, 14:08:09 PM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Madeleine Catherine. Motor. Published at Saturday, December 23rd 2017, 15:37:58 PM. To prevent this, the drive must be set to limit the motor current to its rated value. Because torque is proportional to current, motor torque is constant from zero speed to the corner speed. Above the corner speed, motor current is limited by the motor’s inductive reactance.
By Jessica Mireille. Diagram. Published at Saturday, December 23rd 2017, 14:53:38 PM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).
By Charlotte Myriam. Diagram. Published at Saturday, December 23rd 2017, 11:00:21 AM. Production circuit boards typically start out as thin sheets of fiberglass (about 1mm thick) that are completely covered on both sides with very thin sheets of metal (typically copper). A "standard" circuit board might use a 1 ounce copper process, which means that one ounce of copper is evenly spread across 1 square foot of circuit board. During the manufacturing process, wire patterns are "printed" onto the copper surfaces using a compound that resists etching (hence the name Printed Circuit Board or PCB). The boards are subjected to a chemical etching process that removes all exposed copper. The remaining, un-etched copperforms wires that will interconnect the circuit board components, and small pads that define the regions where component leads will be attached.
By Sasha Sara. Diode. Published at Saturday, December 23rd 2017, 10:43:50 AM. Once the voltage applied to the anode is made more positive than the cathode by an amount greater than the depletion layer potential, forward conduction from anode to cathode conventional current commences.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 10:37:29 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
By Bertille Solange. Circuit. Published at Saturday, December 23rd 2017, 09:32:45 AM. These are commonly termed as IC’s. They are usually in form of chips and microchips. This is a set of multiple electronic circuits on a small semiconductor device (normally silicon). With the advancement of technology, these IC’s prove to be extremely beneficial. They are present in any electronic device you can name. From computers, mobiles to other digital appliances you have multiple IC’s present in them. Their main components are a combination of Diodes, transistors and microprocessors. The microprocessors provide memory to the device. With the help of the microprocessor the electronic devices can perform logical or protocol applications.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 23rd 2017, 07:55:27 AM. An intuitive way to understand the behavior of voltage and current in electronic circuits is to use hydrodynamic systems as an analogue. In this system, voltage is represented by gravitational potential or height of the fluid column, and current is represented by the fluid flow rate.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.