By Jessica Mireille. Motor. Publised at Thursday, December 21st 2017, 11:37:52 AM. A real step motor has losses that modify the ideal speed-torque curve. The most important effect is the contribution of detent torque. Detent torque is usually specified in the motor datasheet. It is always a loss when the motor is turning and the power consumed to overcome it is proportional to speed. In other words, the faster the motor turns the greater the detent torque contributes power loss at the motor’s output shaft. This power loss is proportional to speed and must be subtracted from the ideal, flat output power curve past the corner speed. This now constitutes a practical speed-torque curve.
By Charlotte Myriam. Motor. Publised at Monday, December 18th 2017, 14:50:43 PM. The motor power output (speed times torque) is determined by the power supply voltage and the motor’s inductance. The motor’s output power is proportional to the power supply voltage divided by the square root of the motor inductance.
By Jessica Mireille. Power. Publised at Monday, December 18th 2017, 08:45:14 AM. A variation of the Standard regulator is the quasi-LDO, which uses an NPN and PNP transistor as the pass device. The dropout voltage for a quasi-LDO delivering rated current is usually specified at about 1.5V(max). The actual dropout voltage is temperature and load current dependent, but could never be expected to go lower than about 0.9V (25°C) at even the lightest load. The dropout voltage for the quasi-LDO is higher than the LDO, but lower than the Standard regulator.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 19:23:03 PM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
By Lydie Honorine. Circuit. Published at Saturday, December 23rd 2017, 18:22:12 PM. Double-layer or double-sided PCBs have a base material with a thin layer of conductive metal, like copper, applied to both sides of the board. Holes drilled through the board allow circuits on one side of the board to connect to circuits on the other.
By Alix Loane. Diagram. Published at Saturday, December 23rd 2017, 17:48:37 PM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Charlotte Myriam. Diagram. Published at Saturday, December 23rd 2017, 17:27:05 PM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Jessica Mireille. Circuit. Published at Saturday, December 23rd 2017, 16:11:17 PM. Impedance is one of the most important concepts in electronic circuits. The purpose of impedance is to generalize the idea of resistance to create a component. To capture the behavior of resistors, capacitors, and inductors, for steadystate sinusoidal signals. This generalization is motivated by the fact that as long as the circuit is linear, its behavior can be analyzed using KVL and KCL.
By Cyrielle Marjolaine. Power. Published at Saturday, December 23rd 2017, 16:09:08 PM. In cases where thermal limiting occurs, both the output voltage and current will be reduced. When the output voltage drops below its nominal value, the error signal appearing at the voltage error amplifier will cause it to try and correct the regulator output voltage by driving its output high (and sourcing more current to the pass transistor).
By Madeleine Catherine. Motor. Published at Saturday, December 23rd 2017, 15:37:58 PM. The effect of setting the motor current to twice the rated value. This abuses the motor because it will dissipate four times as much heat as setting the current to its proper value. The actual increase in low-speed torque is considerably less than double because of magnetic saturation of the motor iron.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.