By Jessica Mireille. Motor. Publised at Thursday, December 21st 2017, 11:37:52 AM. The motor power output (speed times torque) is determined by the power supply voltage and the motor’s inductance. The motor’s output power is proportional to the power supply voltage divided by the square root of the motor inductance.
By Charlotte Myriam. Motor. Publised at Monday, December 18th 2017, 14:50:43 PM. To prevent this, the drive must be set to limit the motor current to its rated value. Because torque is proportional to current, motor torque is constant from zero speed to the corner speed. Above the corner speed, motor current is limited by the motor’s inductive reactance.
By Bertille Solange. Diagram. Published at Monday, December 04th 2017, 11:38:56 AM. There are drawing programs, and there are schematic capture programs. All schematic capture programs will produce output for inclusion in publications. However, these programs have different goals, and it shows. Rarely is the output of a schematic capture program really suitable for publication; often it is not even readable, or cannot be scaled. Engineers who really want to have a useful schematic drawing of a circuit usually redraw the circuit in a general drawing program, which can be both tedious and prone to introducing new errors.
By Lydie Honorine. Circuit. Published at Saturday, December 02nd 2017, 11:34:14 AM. A collection of electronic components that have been assembled and interconnected to perform a given function is commonly referred to as a circuit. The word circuit derives from the fact that electric power must flow from the positive terminal of a power source through one or more electronic devices and back to the negative terminal of a power source, thereby forming a circuit. If the connections between an electronic device and either the positive or negative terminals of a power supply are interrupted, the circuit will be broken and the device will not function.
By Charlotte Myriam. Circuit. Published at Friday, December 01st 2017, 09:55:05 AM. Electrical components such as resistors, capacitors, inductors, and transistors can all be represented by equivalent mechanical devices that support this analogy.
By Alix Loane. Power. Published at Wednesday, November 29th 2017, 09:01:12 AM. A variation of the Standard regulator is the quasi-LDO, which uses an NPN and PNP transistor as the pass device. The dropout voltage for a quasi-LDO delivering rated current is usually specified at about 1.5V(max). The actual dropout voltage is temperature and load current dependent, but could never be expected to go lower than about 0.9V (25°C) at even the lightest load. The dropout voltage for the quasi-LDO is higher than the LDO, but lower than the Standard regulator.
By Sasha Sara. Circuit. Published at Monday, November 27th 2017, 07:42:24 AM. We all know about electricity. It is the flow electrons. Hence the word electricity is derived from the word electrons. A battery itself doesn’t work, if you hold it up in air, there would be no passage of electric current. Hence you need a circuit. In Simple terms an electronic circuit is a closed pathway for electrons to flow.
By Valentine Sybille. Power. Published at Sunday, November 26th 2017, 07:35:26 AM. In shunt regulation a resistor is typically placed in series with the load and the unregulated voltage. The resistor is small enough so that the load could always receive somewhat more than the maximum current it would ever need. The shunt regulator is placed across the load and conducts excess current around the load such that the voltage across the load remains a constant as the load draws the actual current at any given time. A common shunt regulator is a Zener diode which is an example of an open loop system. Feedback control can also be used to drive the current through the control element (a transistor) across the load. Shunt regulators are generally only used for low power applications because they can be very inefficient. However, shunt regulators have an inherent fault current limiting feature and also can regulate even if the load is forcing current into the regulator rather than drawing current from it. Shunt regulators also have an interesting feature that the input current is constant – independent of load current (except if a load fault occurs – but that is a special case not in normal operation). Thus shunt regulators are very good at isolating a load with rapid and large current fluctuations.
By Jessica Mireille. Diagram. Published at Thursday, November 23rd 2017, 06:53:21 AM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.