By Jessica Mireille. Motor. Publised at Thursday, December 21st 2017, 11:37:52 AM. A step motor is highly resonant because it is a mass-spring system. The “mass” portion is the rotor and load inertia while the “spring” portion is the restoring torque of the magnetic field that drags the rotor along. Because of this, velocity lags torque by 90 degrees.
By Charlotte Myriam. Motor. Publised at Monday, December 18th 2017, 14:50:43 PM. When using multiple drives from a common power supply, use individual supply and ground wires to each drive and return them to a common point back at the power supply. This is called a “star” power supply distribution; never use a “daisy-chain” power distribution, where the supply and ground wires for the next drives are picked up from the previous one.
By Cyrielle Marjolaine. Diagram. Published at Saturday, December 23rd 2017, 02:43:16 AM. Be sure to use this to produce a schematic if you need to ask questions about your circuit. It will help others to quickly understand the circuit diagrams are pictures with symbols that have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here. Components and connections involved in your design.
By Madeleine Catherine. Circuit. Published at Saturday, December 23rd 2017, 02:15:49 AM. If the components are connected in a parallel format they would be termed to be a parallel series. In this sort of a connection all the components would receive the same voltage, while the current would be divided amongst the components.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 23rd 2017, 01:06:49 AM. We all know about electricity. It is the flow electrons. Hence the word electricity is derived from the word electrons. A battery itself doesn’t work, if you hold it up in air, there would be no passage of electric current. Hence you need a circuit. In Simple terms an electronic circuit is a closed pathway for electrons to flow.
By Alix Loane. Diagram. Published at Saturday, December 23rd 2017, 00:38:09 AM. Circuit components are manufactured with exposed metal pins (or leads) that are used to fasten them to the PCB both mechanically (so they will not fall off) and electrically (so current can pass between them). The soldering process, which provides a strong mechanical bond and a very good electrical connection, is used to fasten components to the PCB. During soldering, component leads are inserted through the holes in the PCB, and then the component leads and the through-hole plating metal are heated to above the melting point of the solder (about 500 to 700 degrees F). Solder (a metallic compound) is then melted and allowed to flow in and around the component lead and pad. The solder quickly cools to form a strong bond between the component and the PCB. The process of associating components with reference designators, loading them into their respective holes, and then soldering them in place comprises the PCB assembly process.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 00:21:25 AM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 23rd 2017, 00:11:04 AM. We all know about electricity. It is the flow electrons. Hence the word electricity is derived from the word electrons. A battery itself doesn’t work, if you hold it up in air, there would be no passage of electric current. Hence you need a circuit. In Simple terms an electronic circuit is a closed pathway for electrons to flow.
By Lydie Honorine. Circuit. Published at Friday, December 22nd 2017, 23:34:06 PM. When multiple components are connected in parallel, the voltage drop is the same across all components. When multiple components are connected in series, the total voltage is the sum of the voltages across each component. These two statements can be generalized as Kirchoff’s Voltage Law (KVL), which states that the sum of voltages around any closed loop (e.g. starting at one node, and ending at the same node) is zero.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.