By Jessica Mireille.

Motor. Publised at Thursday, December 21st 2017, 11:37:52 AM. The result now is a two-part speed-torque curve which features constant torque from zero speed until it intersects the motor’s natural load line, called the corner speed, beyond which the motor is in the constant power region.

By Charlotte Myriam.

Motor. Publised at Monday, December 18th 2017, 14:50:43 PM. Ideally, you will be connecting motors per an installation drawing. In that case, it’s a matter of correctly identifying the motor leads by number and connecting them per the drawing. Don’t try to “wing it” when replacing a motor, working with OEM equipment, or installing a motor when such drawings have been provided. But there’s a catch. We’ll get to that in a moment.

By Charlotte Myriam.

Circuit. Published at Thursday, August 17th 2017, 22:51:19 PM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.

By Bertille Solange.

Circuit. Published at Tuesday, August 15th 2017, 22:28:56 PM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.

By Cyrielle Marjolaine.

Circuit. Published at Monday, August 14th 2017, 20:40:30 PM. The concept of complex impedance introduces a unified representation for resistors, capacitors, and inductors, whereby a circuit’s frequency response from input to output can be determined using KVL and KCL, where each element is assigned the appropriate impedance. The key assumption to this point is that the input to the circuit must consist solely of DC and/or sinusoidal signals. Now, this analysis is be extended to include arbitrary input signals by using the mathematical techniques of Laplace transforms.

By Valentine Sybille.

Diagram. Published at Friday, August 11th 2017, 20:20:28 PM. A capacitor is a two-terminal device that can store electric energy in the form of charged particles. You can think of a capacitor as a reservoir of charge that takes time to fill or empty. The voltage across a capacitor is proportional to the amount of charge it is storing – the more charge added to a capacitor of a given size, the larger the voltage across the capacitor. It is not possible to instantaneously move charge to or from a capacitor, so it is not possible to instantaneously change the voltage across a capacitor. It is this property that makes capacitors useful on Digilent boards and in many other applications.

By Cyrielle Marjolaine.

Circuit. Published at Wednesday, August 09th 2017, 17:27:34 PM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.

By Madeleine Catherine.

Circuit. Published at Saturday, August 05th 2017, 15:56:27 PM. Since single-layer/single-sided PCBs only have their various circuits and electrical components soldered onto one side, they are easy to design and manufacture. This popularity means that they can be purchased at a low-cost, especially for high-volume orders. The low-cost, high volume model means they are commonly used for a variety of applications, including calculators, cameras, radio and stereo equipment, solid state drives, printers and power supplies.

By Bertille Solange.

Diagram. Published at Thursday, August 03rd 2017, 15:32:42 PM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).

Recent post

- Ih 284 Tractor Wiring Diagram
- John Deere Model 50 Engine Diagram
- Dodge Dart Steering Column Wiring
- Honda Odyssey Transmission Wiring Diagrams
- Jeep Cj Wiring Diagram For Starter
- John Deere 2120 Wiring Diagram
- John Deere L118 Wiring Schematics
- Diagram Rover Engine Discovery 2013
- Light Fixture Dimmer Wire Diagram
- John Deere Model A Engine Diagram

Category

Monthly Archives

Static Page

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.