By Jessica Mireille. Power. Publised at Monday, December 18th 2017, 08:45:14 AM. The thermal limit circuit can sink all of the current from the error amplifier output, and keep the regulator output voltage/current as low as needed to maintain the junction temperature at 160°C. As shown, the thermal limiter can "override" the voltage control loop when needed to prevent damage to the IC.
By Cyrielle Marjolaine. Circuit. Published at Monday, December 25th 2017, 19:17:03 PM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.
By Bertille Solange. Power. Published at Monday, December 25th 2017, 18:57:16 PM. In thermal limiting, the output voltage drops and the load current can be reduced to any value (including zero). No performance characteristic specifications apply when a part is operating in thermal shutdown mode.
By Jessica Mireille. Diagram. Published at Monday, December 25th 2017, 18:39:55 PM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
By Sasha Sara. Diagram. Published at Monday, December 25th 2017, 17:26:43 PM. On all but the simplest PCBs, wires must be printed on more than one surface of fiberglass to allow for all the required component interconnections. Each surface containing printed wires is called a layer. In a relatively simple PCB that requires only two layers, only one piece of fiberglass is required since wires can be printed on both sides. In a more complex PCB where several layers are required, individual circuit boards are manufactured separately and then laminated together to form one multi-layer circuit board. To connect wires on two or more layers, small holes called vias are drilled through the wires and fiberglass board at the point where the wires on the different layers cross. The interior surface of these holes is coated with metal so that electric current can flow through the vias. Most Digilent boards are simple four or six layer boards; some more complex computer circuit boards have more than 20 layers.
By Lydie Honorine. Circuit. Published at Monday, December 25th 2017, 17:00:36 PM. A simple low-pass filter circuit, which allows low frequency signals to pass through the circuit while attenuating high-frequency signals, can be made using a resistor and capacitor in series.The transfer function of this filter can be determined by analyzing the circuit as a voltage divider,
By Jessica Mireille. Diagram. Published at Monday, December 25th 2017, 16:13:17 PM. Inductors are usually represented by either a series of curved bumps, or loopy coils. International symbols may just define an inductor as a filled-in rectangle.
By Alix Loane. Circuit. Published at Monday, December 25th 2017, 15:15:32 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.